Do you save your lace scraps? I have a small bag filled with odd-shaped pieces of beautiful lace, just because I can’t bear to throw them out. I love little lace details, so I try to find places to add in small pieces of lace. I had some long narrow pieces of lace left from panty project that didn’t work out, and decided to make up a bralette. This is one of the first few prototypes of my bralette pattern that I have been working on behind the scenes for the last couple months. The shaping of the cradle is a bit different than the final pattern. I added lace overlays to the inner and outer cups, and at both ends of the back band. Intially I had added in a piece at the center front of the cradle, and realized that it looked like a lace box, so I removed the center piece and ended up with something like a butterfly. While I mirrored the scalloped edges, I can see now that the lace pattern itself is not symmetrical. Oops! Mirroring the lace pattern takes some careful attention, and isn’t always conducive to using up scraps of lace. I still love how it turned out, and have been wearing this bralette frequently.
Do you save your lace scraps? Where do you like to add them in on your sewing projects?
2 Comments
Here it is, my first bra made with my custom bra sloper using the drafting method from Bare Essentials Bras, 3rd Edition by Jennifer Lynne Matthews-Fairbanks. Pattern: self draft, 2-piece vertical seam cups with full frame. Underwire: Carmen by Emerald Erin Fabrics: Grey duoplex and powernet I think from Bra Maker's Supply. Elastics: 3/8" & 1/2" black picot elastics from Fabric Depot Co. Piping edge elastic along the neckline from Sew Sassy. Straps: 1/2" ruched strap elastic. Can't remember where I bought it, sorry. Bow: 1/4" satin ribbon, heart charm from Joann jewelry department. While I would not say that sewing a bra is hard, there are always a few parts I struggle with. Every time I sew a bra, I try out a new technique or two to see if I can improve my sewing experience.
This time around, there were two areas I wanted to try something new: encasing the ends of the channeling at the front, and making a strap attachment less bulky. For the channeling, I'd normally have the ends extend past the edge of the cradle, then close them off and trim them at the end after everything else is sewn. I think I learned this method from the Harriet Bra instructions. But after seeing a few Emerald Erin bras that use the neckline elastic to finish the top of the cradle as well as the cups, I decided to see if I could get the ends of the channeling under the edge of the neckline elastic. I started the channeling 1/4" down from the edge, since I was using 1/4" elastic. I didn't quite get the ends under the elastic, but at least they aren't sticking out past the top of the cradle. I usually attach the ring to a strap attachment that is part of the cup. So far that has led to a very bulky seam that usually breaks my needle with several layers of fabric and elastics all coming together. This time I decided to just let the armhole elastic extend past and thread the ring through that. I probably should have made a tighter loop against the cup; it stretches out a bit when worn, obviously because it is elastic. But this join was much easier for me to execute and left me with a much smoother fold. Do you have any tips for sewing channeling or attaching the straps? I'd love to hear them, leave a comment below. Happy Sewing! In my previous post, I talked about creating a custom bra draft using the method from the book Bare Essentials Bras, 3rd edition by Jennifer Lynne Matthews-Fairbanks. After finalizing the fit of the bra draft, the 3-piece cup, cradle and band are turned into a sloper to make custom bra designs. What is a sloper?A sloper, in fashion industry terms, is a basic building-block pattern without seam allowance or design lines. It is used as a starting off point to create various designs. For a bra, the sloper includes a basic cup, a cradle without bottom shaping and a back band. Here's a peek at my sloper, drafted in Adobe Illustrator.
I'll begin this post by saying I have not been paid in any way to endorse or give a review of this book. I'm just a bra-making fangirl giving her opinion!
I was so excited when Jennifer Lynne Matthews-Fairbanks came out with the 3rd edition of her book Bare Essentials: Bras. This new edition has a whole new drafting method that takes into account torso size and shape for a completely custom fit! I have the previous edition of her book and found it monumentally helpful for drafting bra patterns. I haven't been completely satisfied with my Shin draft, (there were too many unexplained variables in the drafting instructions) so I wanted to try a different drafting method and compare. Yesterday I sewed my first Darcey Bra by Evie La Luve. My feelings about it are a bit mixed, but I think I will sew myself another Darcey Bra in the future with some modifications to the fit and the fabric choice.
Hello sewing friends! I'm back to share another bra project with you. It seems like every bra I make is an experiment, and there is always something I want to do differently on the next one.
Yesterday I made my first partial band bra! Back when I wore store-bought bras, partial band styles were what I usually went for. So why did it take me so long to make one? Well... I guess I wanted to perfect the fit on my full-frame bra before jumping into more patternmaking with a totally different style.
I followed Beverly Johnson's instructions (from her Bluprint class "Sewing Bras: Designer Techniques") for making the partial band pattern, and I have to say it made me nervous. I understood adding an allowance for the channeling to the cups, but removing the seam allowance from the bridge just didn't seem right. But Beverly must have read my mind because she even said it might not seem right and to just trust her. I made a new bra today, and I'm quite pleased with how it turned out. I'll start off by saying my dress form doesn't really fill it out properly; it fits me perfectly! This is the diagonal seam cup I tested out on my bra fitting band. The lace sling is the same pattern piece that I used in my black lace balconette, but in this case is purely decorative and not functional as a powerbar.
Today I made a bra fitting band following the instructions on the Merckwaerdigh blog. A bra fitting band serves two purposes: 1. When first fitting a bra pattern, after finding the correct wire, the next step is to fit the band. It is easier to fit the bra in steps than try to fit the underwire, band and cups all at the same time. 2. Even though I now have a well-fitting bra pattern, I want to try out different bra cup designs, and rather than make an entire bra every time I make a style change, I can sew up a single cup to check the design and fit. To begin, cut out the bridge, cradle, and back band pieces. Since this is only for fitting, I cut a single layer of simplex for the bridge and cradle and didn't bother with lining. Sew the elastics on as usual. This would be a good opportunity to use up scraps, and you could zigzag together shorter pieces if necessary. I didn't happen to have any scraps in the correct widths, so I just used white. If I was sewing a regular bra, the next step would be to sew the channeling to the cup/cradle seam allowances. Since I don't have a cup, I marked out the seam allowance on the cradle and sewed the channeling below the markings. I sewed the channeling to the inside of the bra, but it could work on the outside as well. Finish the underarm elastic as usual. As you can see in the picture below, I inserted the wires and closed the channeling at the center front. Don't do that! As soon as I started to sew on a tester bra cup I realized the underwire would be in the way (duh) and I had to unpick the seam. So leave one end of each channeling open. And here is the fitting band on my dress form. The straps are just pieces of elastic, I figured it would be simpler to pin the front of the straps to the cups and didn't bother with rings and sliders. Now the new cup styles. My self-drafted bra has horizontal cup seams, and I wanted to try both vertical and diagonal seams. I cut and sewed one cup in each style, with the vertical seam as a right cup and the diagonal seam as a left cup. After removing the underwires from the channeling, I basted the cups into my fitting band, keeping in mind that extra seam allowance would stick out at the underarm edge that would normally be finished with elastic. Looks like I forgot to add seam allowance to the neck edge of the vertical cup. Oops! Now pop the underwires back in and try it on. My dress form is not as squishy as I am, and doesn't have as much lower cup fullness as I do. The diagonal seam cup fits me very well and doesn't seem to need any changes. There is some weirdness in the fit of the vertical seam cup. Horizontal wrinkles in the lower part of the cup seem to indicate not enough room, and the bulging above the apex means there is too much curve in the seam. Looks like I have some alterations to work on!
In my previous post, I shared how I altered the Barrett Bralette pattern to fit me. Last week I realized that most of my old sports bra are falling apart, so it was time to cut out another Barrette. I have a large pile in the corner of my bedroom of clothing and other items that are going to be donated to the local thrift store. My husband likes to fling just about every old thing into the pile, without really discerning whether anyone would actually be likely to buy it. One of the pieces of clothing in the pile was an old t-shirt, which had a neck band that was stretched out. I really liked the fabric, a cotton/poly jersey in blue and black, and decided that since it was too worn out to donate I would cut it up into a couple sewing projects. So far, that one t-shirt has turned into two pairs of panties and a bralette. I'd say that is a pretty good deal! It bothers me when trims don't perfectly match the fabric color, so I tend to go for contrasting colors. I had some magenta picot elastic (from Lace Heaven) and I really like the bright pop of color it adds. The back band is black powernet. This time around I didn't add a lining to the cups, so I topstitched the seam allowance open. We shall see if the raw seam allowances are irritating to my skin or not. Also, I used my 1" black elastic again for the straps and band. If you read my previous post, you know why!
Have you cut up old clothes and turned them into new creations? Yesterday I finished sewing my second Barrett Bralette, a free pattern from Madalynne. Before I share my newest project with you, I wanted to share my first Barrett Bralette and how I altered the pattern to fit me. It seems like this sort of bralette only works well on small cup sizes, so when this pattern was published I was anxious to see how it worked on women with small rib cages and larger cup sizes. On Instagram I saw Barrett Bralettes on a wide variety of figures, and realized I had two options for altering the pattern to work for me. For reference, my underbust measurement is 31.5" and my full bust measurement is 37". I usually wear a 32D in my handmade bras. Options for altering the pattern: 1. Use a large cup size and pair it with a small band. 2. Use a small size appropriate to fit my underbust measurement and increase the projection. I decided to go for #2, since most of my fullness is in the lower cup, and I prefer not to have a lot of fabric in the upper cup going towards my armpit. According to the pattern directions my underbust measurement would have technically put me in an x-small, but I decided that would probably be too tight and cut a size small instead. At the apex (fullest part of the bust) I added 3/8"on both the center front and side cup pieces and gradually blended back to the size small. Why 3/8"? To be honest, it was just an educated guess and luckily it worked for me. I cut my project from cotton/lycra jersey and lined it with stretch mesh. I planned to use this bralette as a sort of sports bra, but I don't do very vigorous exercise so a super supportive bra was not necessary for me. One of the changes I decided to make was to use 1" elastic as both the straps and the entire back band. Why elastic only? Well, there's a story to tell and I'll get to that once I finish showing you my bralette. I used the back band pattern piece as a guide and cut three lengths of elastic. I basted them to the edge of the side cups, then topstitched down the entire seam. To secure the straps to the back elastics, I sewed a zigzag box over all the crossing points. I'm quite happy with the fit and feel that it gives me a good amount of support for a bralette. I think using a strechy-but-firm knit fabric really helps to provide support, and so does adding a mesh lining. I like to show the guts of my bra makes, even if they are a bit messy. Please excuse any wonky stitching. Now.. why did I use so much 1" wide black elastic? Because I have lots of it. Lots and lots of it. My husband spent all of 2016 stationed in South Korea, about 20 minutes from Seoul. He is a brave and adventurous type (and also has a degree in anthropology), so on his days off he'd hop on the subway, pick a random exit, and just explore the surrounding area. One day, he happened to stumble upon Dondaemun, Seoul's fabric market. Seven floors of fabric, trims, and commercial embroidery and sewing. He was amazed by all the vendors and wanted to get something for me. At that time I was beginning my bra-making journey, so I sent him swatches of the plush back elastics and straps that I was looking for. While I am blessed to have a husband that is eager to do nice things for me, he doesn't quite have the eye to pick out things that match the samples I give him. He found a vendor selling this black elastic and thought he had hit the jackpot. The vendor did not speak English, but through a few Korean words and gestures, Aaron thought he communicated that he would like five yards of elastic. The man nodded and began unrolling the elastic and measuring. And measuring and measuring, and unrolling and unrolling. Aaron became alarmed when the pile of elastic grew bigger and bigger and quickly looked up the Korean word for five (daseos) and waved his five fingers. The man nodded his head and just kept measuring. Aaron's friend said "Dude... I think you're getting that whole roll." Sure enough, that is what happened. The man shoved all the elastic into a grocery bag and wrote up the bill... which, translated into American dollars was a grand total of $15. Hah! Quite a good deal. While not plush back elastic, it is quite soft against the skin, and not overly firm like packaged elastic. So I am happy to use it in sports bras and waistbands. I put my bralette on my form to check the strap placement and realized that with my latest pair of briefs (from the pattern I am developing, stay tuned!) I had inadvertently created a matching set.
Have you tried the Barrett bralette? What do you think of the fit? Also, have you been to any of the amazing fabric markets around the world? Have you found any good fabric and trim deals? A couple weeks before Valentine's Day, someone in the Bra Makers Group on Facebook mentioned quarter-cup bras and it got me thinking about barely-there bras more suitable for boudoir than everyday wear. Later on I came across this series on power bars by Silver Lining Atelier, and this bra in the photos. Thinking back to the discussion on quarter-cup bras and my interest in trying out an internal power bar, I decided to try making my own version of this bra. My self-drafted bra has a horizontal cross-cup seam, so in order to make the scallop edge of the lace across the top edge, I needed to draft a one-dart cup. In Beverly Johnson's bra-making classes on Bluprint (formerly Craftsy) she uses bra foam to sew up a cup, then draw the new seamlines and cut it apart to form the new pattern pieces. I only have a small amount of bra foam, and I didn't want to use it up so I wondered what else I had on had to use as a substitute. Felt! I had lots leftover from making Christmas stockings. After trimming off the seam allowances, I used a 3-step zigzag to sew the cup pieces together. After sewing the cup, I realized that the dart would be right where the lower cup seam was, so I just cut open where I sewed. Seems a bit counterproductive, and there is probably a more accurate way of doing it with the paper pattern. I'm sure I'll learn someday! So to make the balconette cup, I cut off the cup about 3/4" above the end of the dart. I should have checked the measurement of the top of the cup, but I didn't and it ended up being too big. I unpicked some of the sewing on the narrow elastic and shortened it to create more tension across the top of the cup. Still not a snug fit, but this bra is more for show than function. While the fit isn't perfect, I'm quite happy with how the overall design turned out. The power bar does it's job and directs the breast tissue toward the center.
This is the second bra made from my self-drafted bra pattern. My first bra from this pattern had a few issues, mainly fabric bunching up at the side of the band and not enough room for the wires. I changed the angle of the frame/band to go more downwards, and raised the underarm edge to provide more coverage and leave some room for wire play. The fabric is a 15 denier nylon sheer from Sew Sassy. Elastics are from Lace Heaven. I used two layers for the cups, cut with opposing stretch and sewn separately. After I finished sewing both layers of cups I realized it would have been better to sandwich the layers so I wouldn't have to worry about the seam allowances overlapping perfectly. To finish the neckline, I sewed bother layers of the cups together, then sewed 1/8" elastic in the seam allowance. Clear elastic and I do not get along, so 1/8" elastic is the best I can do. To prevent the cross cup seams from drifting apart, I lined up all the seams used a narrow zigzag over the lower cup seam. We'll just call that a 'design feature'. Funny story about the cradle lining; I only have white and black, and since this fabric is so sheer I wanted a nude color. So I thought since I had some brown Rit Dyemore, I'd just do a quick dunk in a dyebath. Well, I added too much dye and the fabric very quickly became a chocolate brown. Oops! I used a different method of strap attachment and it was much less stressful, and I didn't break any needles. Before sewing on the underarm elastic, I lined up the edge of the strap with the neckline edge and sewed them RS together. Then when I went to sew the underarm elastic I made the edge as close as possible to the strap, so that when the elastic flipped back it would lay nice and smooth.
I'm quite happy with how this bra turned out. There is still a bit of bunching at the sides, so I'll work on that more. The wires also still don't have a lot of room to move around, so I'll check my pattern against the wire to see if the error is in the pattern or my sewing. As I mentioned in my previous post, I have dived down the rabbit hole of drafting my own bra patterns. While I really love my Harriet bras, after wearing them for awhile the wires start to poke me at the sides of my breasts and leave bruises. I wondered why an otherwise well-fitting bra would do this, so I did a bit of research and began to learn about breast shape and the different underwires available to fit them. Just as overall bodies come in various shapes and sizes, so do breasts. This blog post from LilypaDesigns was really helpful in learning about shapes and distribution of fullness, and Emerald Erin's guide on underwire styles was very interesting. I found I am wide set, with wide roots and bottom fullness. While I could try out various patterns from other people and fiddle with the fit, my stubborn determination kicked in and I decided to just make the pattern myself. Enter my new favorite book: Patternmaking for Underwear Design by Dr. Kristin Shin. This book covers all sorts of lingerie design, not just bras. It reads much like my patternmaking textbooks from college; the draft is shown in a standard size (34B) and it is up to you to implement your own measurements. There is no handholding at all, so if you are unfamiliar with patternmaking it might be a challenge. It all begins with fitting the underwire. Some blogs I read recommended ordering wires in different sizes and seeing which one worked best. This seemed a bit willy nilly to me, and since I already have several sets of wires that were too narrow I didn't want any more. I wondered if I actually needed a completely different style of wire. Luckily, I read about making a breast root trace. You can read about it here, just be warned that there are photos of a somewhat naked breast. I don't have a flexible ruler, so I used some jewelry-making wire doubled up. In the photo below you can see my root trace compared with the size 38 underwire which seems to fit me perfectly. Now that I had a well-fitting underwire, I began drafting my pattern. I took various measurements indicated in the book and did my best to follow the diagrams. The only thing that confused me was the angle between the cradle and band. The directions were rather vague, and this ended up causing some fit issues with both the bras that I have made from this pattern. And now, here is my first bra made from my self-drafted pattern. Go ahead and snicker at my funny looking lace butterfly. I had little bits of this lace leftover from a Harriet bra, but I ended up making the wings too small. Oh well. The outer cup and frame fabric is duoplex. There are actually no underwires in this bra, because they didn't fit into the casing! Somehow Dr. Shin forgot to accommodate for wire play, and there simply wasn't enough room to jam in the wires without them sticking out from the top of the bridge. My dress form isn't quite as big as I am, so the bra isn't quite filled out. When I first started making bras I wondered what sort of finishing bra-makers did, so I like to share the guts of my bras so others can see. I line my bra cups with 15D tricot. As you can see, I was struggling with my feed dogs while sewing the elastics. My sewing machine is pretty new, and we are still getting acquainted.
So what did I change? Most importantly, adding in some wire play. That means raising up the top of the cradle/band seam 1/2" so the wire have room to move a bit and won't jam into my sides. I need more coverage in that area anyway, thanks to what I lovingly call my armpit fat. Remember how I said the instructions were a bit vague on the angle of the cradle/band seam? Well apparently I didn't make it angle down enough, and ended up with fabric bunching up on the sides. To fix this, I have angled the band down more at the top, adding about 3/8" at the top of the cradle down to 0 at the bottom. Also, I'm not a fan of sewing the O-rings at the top of the cup. I appreciate that it makes the straps easy to adjust, but all those layers usually make me break a needle. I'm trying out a different strap attachment next time. Have you tried to draft your own bra? Was it a successful fit? What resources were helpful? Why do I make my own bras? Because I want them to fit properly! I'm sure you've heard over and over that most women wear the wrong size bra. I spent most of my adult life wearing a 34B, and always had a problem with the band riding up and the straps falling off my shoulders. In addition to that, I felt like I just wasn't getting a lot of support. I got a bra fitting and was told yes, you are a 34B. So I decided that was just as good as it got and I just didn't have the right shape to fill in my bra properly and have cleavage of any sort. Fast forward to 2015 and I'm living in North Carolina. After spending my first 27 years in a hot and dry desert in California, living in a very humid subtropical environment is a big shock to me. Every time I left the house, the wet wall of hot air would make me feel drenched, and I'd have to change my clothes after coming home. The worst of it was my bras. I could literally wring the sweat out of them, and I really didn't enjoy feeling like I was wearing a damp sponge. So I went shopping to look for a plain cotton bra with no foam cups. But, guess what? Apparently, there was no such thing! I looked at every store I could think of, and it was all thick molded cup bras in synthetic fibers. I decided it was time to look into making my own bras. At that time, bra-making wasn't as popular so I it was difficult finding the right resources and patterns. I made a few bralettes in cotton jersey, which weren't supportive but at least I felt comfortable at home while wearing them. After I moved to central Texas, another hot and humid subtropical area, the Watson Bra by Cloth Habit became very popular. On social media it seemed like every sewist in the world was making them. Eventually I bought the pattern and made myself a few, and I finally found relief from spongy cups and got a decent fit and support. When the Harriet Bra was released, I was in love. It was such a pretty design, and I had never had a lace bra. So I bought the pattern and carefully read the directions. When I measured myself to determine my size, I laughed out loud. 32D, yeah right! I had always thought of D-cups as big, and I definitely was not big. I ignored the sizing and made my first practice bra in 32C and... it was way too small. As in comically small. Alright, I guess I should have made 32D. So I made another bra, and was suprised that the fit was better. Somehow I still thought I'd be swimming in it, but I filled out the cups nicely. I made two more Harriet Bras, tweaking the fit each time. For the first time, I felt very supported and lifted. My clothes fit better, and I wasn't fiddling with the straps and pulling down the band. While out shopping one day, I peeked at the bras (the dreaded foam cups) just to see if they had my size. No 32Ds in sight. So now that I know what size I should really be wearing, bra-making has become more of a necessity. I have recently jumped into drafting a bra pattern using my own measurements, which has been an adventure all on its own and will be a blog post for another day.
Do you make your own bras? If not, is there something about it you find intimidating? |
CassieI design lingerie sewing patterns for everyday comfort and feminine style in an inclusive size range. Fill up your underwear drawer with beautiful custom-made bras and panties in your favorite fabrics and trims, designed to fit your body. Categories
All
Archives
March 2024
|